3.1 CCNA 2 - Module 9

1	After issuing the command traceroute 192.168.4.2 from Router A, the following information is returned. Tracing the route to Router_D (192.168.4.2) 1 Router_B (192.168.2.2) 16 msec 16 msec 16 msec 2 * * * 3 * * * What can be concluded about the network shown in the graphic based on the output given? Network 192.168.5.0 is missing from the routing table on Router A. There is a problem with the connection between Router B and Router C. Router C is not running CDP. Some of the routers are non-Cisco devices. Router B was not able to return ICMP TEMs to Router A.
2	Which of the following would be the default administrative distance of a static IP route that references the IP address of the next hop? 0 1 5 20
3	After issuing the show interfaces command, a technician notices the line "Serial1 is down, line protocol is down" in the output. Which of the following are possible reasons for this message output? (Choose three.) There is a mismatch in the encapsulation type on both ends of the link. A Layer 1 issue exists. An interface problem exists. The clockrate was not set during configuration. There is no usable media for the protocol. Keepalive messages are not being sent.
4	Which three correctly pair a routing metric with its description? (Choose three.) hop count - the number of routers traversed to reach a destination bandwidth - the amount of time it takes a packet to travel a link load - the amount of activity on a link delay - the link speed reliability - the error rate on a link
5	When issuing the show interfaces serial1 command, a network administrator receives the output shown in the graphic. What are the possible causes of an increase in the number of input errors? (Choose three.) There could be Layer 3 addressing problems. There could be a problem with faulty telephone equipment. The router hardware could be defective. There is an incorrectly configured encapsulation on the interface. There could be a problem with the cabling.
6	Which ICMP message type notifies source hosts that a receiving host or network is not available? time exceeded redirect destination unreachable source quench parameter problem echo reply
7	The show interfaces command provides line and protocol status information. Which of the following conditions would never occur in the output of this command? serial1 is up, line protocol is up serial1 is up, line protocol is down serial1 is down, line protocol is down serial1 is down, line protocol is up serial1 is administratively down, line protocol is down
8	The network administrator shown in the exhibit can ping the E0 interface of the HAR router, but the telnet intranet.xyz.com command issued from the administrator's workstation fails to open a session with the intranet.xyz.com server. What are two possible causes of this problem? (Choose two.) upper-layer application problems domain name system problems IP addressing problems on the HAR router clock rate problems on the HAR router serial interface ICMP connectivity problems
9	The network administrator is using a PC to access a router via the router console port. Both the PC and the router are powered on and a cable has been connected between them. However, a session cannot be established. Which steps might fix this problem? (Choose two.) Verify the cable is properly connected at each end. Reseat the network card in the PC. Verify the cable is the correct type. Verify that a password has been set on the console line. Check the transceiver for link lights. Reseat the console card on the router.
10	Which command will display routing table information about all known networks and subnetworks? Router# show ip interfaces Router# show ip connections Router# show ip route Router# show ip networks
11	A network technician has discovered that a router in the network can no longer be reached. The technician attempts to verify Layer 1 functionality, but is unable to physically inspect the cables. Which command can be used to determine the type of cable connected to the router? Router# show interfaces Router# show controllers serial Router# show ip route Router# show ip protocol Router# show version Router# show running-config
12	During the lookup process when forwarding a packet, a router checks its routing table for the best path to the destination. If a route has an administrative distance of 0, what does this indicate to the router? The packet should be discarded. The destination is unreachable. The destination is a directly connected network. The source of the update for that route is unreliable.
13	Which command will verify the functionality of all seven layers of the OSI model on a network host? ping debug telnet traceroute
14	After issuing the show interfaces serial1 command, an administrator notices an increasing number of carrier transitions. What are the possible causes for this increase? (Choose two.) There is an incorrect encapsulation configured on the interface. There could be an interruption in the line by the service provider. There is a faulty switch or CSU/DSU. There is noise on the serial line.
15	Consider the RIP network shown in the diagram. Which entries would be listed in the routing table of Router A? R 192.168.5.2[120/1] via 192.168.15.0, 00:00:09, Serial0 R 192.168.15.0[120/1] via 192.168.5.2, 00:00:13, Serial1 R 192.168.15.0[120/1] via 192.168.5.1, 00:00:13, Serial0 R 192.168.5.1 [120/1] via 192.168.5.2 00:00:29, Serial1 R 192.168.15.0 [120/1] via 192.168.5.2, 00:00:29, Serial1 R 192.168.5.1 [120/1] via 192.168.5.2 00:00:18, Serial0 R 192.168.15.2 [120/1] via 192.168.5.2, 00:00:18, Serial0
16	Which items would be displayed when the show ip protocols command is executed? (Choose three.) sources of routing updates networks being advertised routing protocol up or down configured routed protocols Layer 2 status of the interface update timer values
17	Which two are true regarding the debug commands? (Choose two.) Debug commands may be issued from the user EXEC prompt. The command undebug all will turn off all debug operations. By default, the router sends the debug output and messages to the telnet session. The high processor overhead incurred using debug may disrupt normal router operation. The debug all command provides a summary view of router activity and can be used frequently for troubleshooting. The show debugging command will display current events such as traffic on an interface and error messages generated by nodes on the network.
18	A network administrator suspects that a network is not being included in the routing updates. Which command will provide information on when the next update is due and which networks are advertised in the update? Router# show interfaces Router# show controllers serial Router# show ip protocols Router# show ip route Router# show running-config
19	Which of the following is a problem at the physical layer of the OSI model? incorrect file formatting incorrect encapsulation on a serial interface incorrect routing protocol incorrect cable type
20	When the show cdp neighbors command is issued from Router C, which devices will be displayed in the output? D, SWH-2 A, B, D SWH-1, SWH-2 B, D SWH-1, A, B A, B, D, SWH-1, SWH-2
21	Which of the following are advantages of using a static route? (Choose three.) secure operation highly adaptable low maintenance configuration low processor overhead precise control of path selection
22	Which of the following commands can be used to statically configure default routes? (Choose two.) ip static-route ip route ip network-route ip default-network ip default-static
23	Why does a router build a routing table? (Choose two.) to list available routes for forwarding data to map local Layer 2 addresses to the remote Layer 3 destination address to dynamically send periodic updates regarding the router's status to prevent routing loops when redundant links are added to the network to select the best path to a destination
24	Which of the following lines from the show interfaces output would indicate a Layer 2 problem? Serial1 is up, line protocol is up. Serial1 is up, line protocol is down. Serial1 is down, line protocol is down. Serial1 is administratively down, line protocol is down.